How To Fix A Water Heater Pilot Light

If pilot flame still won’t stay lit, call professional service person. You’ll get your hot water going without waiting for a pro to show up and save the cost of a service call for a gas water heater repair. Near the gas regulator valve, you’ll find the temperature control valve. Set the thermostat to your desired temperature. If it is, turn the gas valve back to “On” and set the temperature to your desired setting. The danger and risks can be incredibly high when it comes to the ignition of gas and could result in death. For example, pilot lights could go out if there are high winds/drafts and low gas pressures but it could also be faulty, loose or broken vents, valves, thermocouples or heat exchangers. When a water heater pilot light goes out, it usually means that a natural change in gas pressure extinguished the flame. When natural gas consumption peaks, the “gas grid” in your area may be nearing its capacity and lower the gas pressure intermittently. This flame ignites the gas that is being provided to the boiler, which in turn produces the heat that we need to warm our homes, heat up our radiators and produce the warm water we wash with.

How To Fix A Water Heater Pilot Light assembly back into place

The pilot light will ensure that the gas is constantly being burnt and producing the heat we desire. 1. Turn the gas control knob to the “off” position and set the thermostat in your house to the lowest setting. On some water heaters, the lowest setting is labeled for pilot lighting. Step 3: Switch valve to pilot setting. STEP 3: Turn your furnace back on. Step 4: If the light doesn’t stay lit, you could have a clog or other serious issues. Check the pilot light. If you think a draft is causing the issue you will need a Gas Safe Engineer to check how your boiler has been installed as they should not be exposed to drafts. If that doesn’t work, clean it: shut off both the water heater gas valve and the main gas line near the heater. The main burner under the tank should light and begin heating the water in the tank.

How To Fix A Water Heater Pilot Light and the main gas

Attempts to re-light the pilot light are futile. Is the boiler pilot light out? Do make sure you remove others from the area before attempting to relight your pilot light to ensure maximum safety to those around you. After replacing the damaged thermocouple with the new one, slide the burner assembly back into place, reattach the tubes, and then relight the pilot light as described above. When you see your pilot light out, you can usually relight it. A: That depends on why the light blew out. 5. A draft is blowing the pilot out. If your pilot light re-lights easily after going out overnight, it’s possible it was blown out by a draft. But, before you begin, it’s important to take the necessary precautions to ensure the safety of yourself and your home. That’s why you should never take a pilot flame outage lightly. Use a long lighter to light the furnace pilot light. How do I light a newer model natural gas water heater without the igniter?

How To Fix A Water Heater Pilot Light Gas Safe Engineer to

Switch your gas regulator valve from “Off” to “Pilot. Ensure you only hold the switch down once the pilot light has ignited, to reduce the chances of any gas accumulating again. This will be located under the gas valve; some water heaters just have an open gap instead where you can see the pilot light burner. To learn how to light your gas fireplace if it has a key, read on! If it’s off, turn it to pilot and hold it down (this causes gas to flow).- When holding it down, you should be able to hear gas flow (it’ll be very faint noise). If you don’t smell gas, it’s likely a minor mechanical issue that you can solve through re-lighting or calling a pro. In most cases, re-lighting your pilot is simple. A dirty pilot light orifice hinders gas flow, but the fix is simple. It could be down to something as simple as the need to refill the gas/propane tank.

How To Fix A Water Heater Pilot Light light orifice

Under constant exposure to a hot flame, a thermocouple wears down over time. If it doesn’t light the first time, wait a few minutes and try again, this time holding the reset button down for 45 to 60 seconds. Do not light a flame or turn on an electric switch until the problem is addressed. A trained technician will identify your problem and provide an appropriate solution. Because you will be using one hand to depress the valve/red button and one hand to light the pilot, you may need someone to hold a flashlight for you if extra light is needed. To light your gas fireplace, first access its control panel and turn the shutoff valve so the handle is parallel to the gas line, which will allow gas to enter your fireplace. Smell for gas. Spend a few minutes checking the area for strong gas odors. If you smell any gas, allow the smell to dissipate for 15 minutes.

How To Fix A Water Heater Pilot Light gas that is being